We are more than an aluminium alloy solution provider.
Do you need consumer aluminium alloy products or learn more info about aluminum alloy prices?
Ultimate Tensile Strength: 310 MPa: 45000 psi AA; Typical: Tensile Yield Strength: 276 MPa: 40000 psi AA; Typical: Elongation at Break: 12 %: 12 % AA; Typical; 1/16 in. (1.6 mm) Thickness: Elongation at Break: 17 %: 17 % AA; Typical; 1/2 in. (12.7 mm) Diameter: Modulus of Elasticity: 68.9 GPa: 10000 ksi AA; Typical; Average of tension and
7 rows The fatigue strength of 6061 aluminum alloy is 96.5 Mpa (14000 psi), which is calculated using
Multipurpose 6061 Aluminum Z-Bars. The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it\'s easy to machine and
Alloy 6005 is similar to alloy 6061. When produced to a -T5 temper, it has the same minimum tensile and yield strength as 6061-T6 and better mability and strength properties than 6063-T6. Alloy 6005A may also replace 6061 due to its better extrudability and surface appearance. Both alloys have excellent bending properties but are not
Aluminum 6061-T6; 6061-T651. General 6061 characteristics and uses: Excellent joining characteristics, good acceptance of applied coatings. Combines relatively high strength, good workability, and high resistance to corrosion; widely available. The T8 and T9 tempers offer better chipping characteristics over the T6
View our aluminum materials here. Home; About. Downloads; Materials. Aluminum; High Temp and Super Alloys; Stainless Steel; 6061: 0.4-0.8: 0.7: Thickness (Inches) Tensile Strength (KSI) Ultimate – Min Tensile Strength (KSI) Ultimate – Max Tensile Strength (KSI) Yield – Min Tensile Strength (KSI) Yield – Max Elongation % Min in 2
6061 - T6 Extrusions. Aluminium alloy 6061 is a medium to high strength heat-treatable alloy with a strength higher than 6005A. It has very good corrosion resistance and very good weldability although reduced strength in the weld zone. It has medium fatigue strength. It has good cold formability in the temper T4, but limited
The breakdown of the alloying elements in 6061 aluminum is as follows: 0.6% Si, 1.0%Mg, 0.2%Cr, 0.28% Cu, and 97.9% Al, and its density is the about the same as pure aluminum (2.7 g/cm 3, 0.0975 lb/in 3). 6061 aluminum gets even larger strength gains with the heat treatment process and is commonly found in T6 and T4 tempers. Its benefits have
6061 aluminum strength depends on the tempered grade, including 6061-O, 6061-T4, and 6061-T6. With 6061-T6, for example, the parameters for measuring how strong it is depends on the yield and tensile strengths. The yield strength of a material measures its allowable stress limit when force is applied to it. When the force exerted is
Mechanical properties of aluminum alloys - tensile strength, yield strength and more. Aluminum alloys are divided into the wrought and cast categories according to how they are produced. The wrought category includes rolling, extruding, drawing, forging, and a number of other more specialized processes. Cast alloys are poured molten into sand
General 6061 characteristics and uses: Excellent joining characteristics, good acceptance of applied coatings. Combines relatively high strength, good workability, and high resistance to corrosion; widely available. The T8 and T9 tempers offer better chipping characteristics over the T6 temper. Applications: Aircraft fittings, camera lens
T6 aluminum square tubing, available in both 6061 and 6063, has an ultimate tensile strength of at least 42,000 psi, yield strength of at least 35,00 psi, and maximum shear strength of 27,000 psi. When the direction of force is known or controlled, aluminum square tubing is considerably stronger than aluminum
The mechanical properties of 6061 depend greatly on the temper, or heat treatment, of the material. 6061-0. Annealed 6061 (6061-0 temper) has maximum tensile strength no more than 18,000 psi (125 MPa), and maximum yield strength no more than 8,000 psi (55 MPa). The material has elongation (stretch before ultimate failure) of 25-30 %.
6061 Aluminum plate (also known as 6061-T651) is one of the most versatile grades of heat treatable aluminum alloys. Ultimate Tensile Strength, psi: 45,000: Tensile Yield Strength, psi: 40,000: Elongation at Break: 12%: Hardness, Rockwell B: 60: Modulus of Elasticity, ksi: 10,000: Back to product
The yield strength is the measure of the maximum amount of stress that will not permanently (or just “elastically”) deform a specimen of alloy (to learn more on this topic, feel free to read about it in our article all about 7075 aluminum alloy).When comparing 6061 and 7075 aluminum’s yield strengths, it is evident that 7075 aluminum is far superior by a
Yield Strength. Less than 10,000 psi. 30,000 psi to 39,999 psi. 40,000 psi or greater. Maximum Temperature. 250 Anodized Multipurpose 6061 Aluminum Hex Bars. A hard-anodized coating forms a bond with the aluminum surface to improve wear and corrosion resistance. Multipurpose 6061 Aluminum
Developed in 1935, 6061-T6 aluminium is a precipitation-hardened aluminium. Precipitation hardening uses high temperatures to increase the yield strength of aluminium. Precipitation hardening lowers the plasticity and hardens aluminium into 6061-T6. 6061-T6 has a density of 2.70 g/cm³ (0.0975 lb./in³) and is remarkably pure, with
This study focuses on the effects of high strength aluminium alloy 6061-T6 at elevated temperatures. The melting point of aluminium alloy 6061-T6 is found
Some steels and other materials exhibit a behaviour termed a yield point phenomenon. Yield strengths vary from 35 MPa for a low-strength aluminum to greater than 1400
The yield strength is the measure of the maximum amount of stress that will not permanently (or just “elastically”) deform a specimen of alloy (to learn more on this topic,
The Aluminum 6061 T6 Chequered Plate is used mostly for structural applications and it is one of the main forms in which the aluminum plates are sold. The material has
The T4 condition allows 6013 aluminum to be formed and demonstrates better stretch forming characteristics. The part can then be aged to the T6 condition without
Yield strength measures the amount of force required to cause a material to deform permanently. Aluminium 6061 has a yield strength of
Tensile Yield Strength: 276 MPa: 40000 psi: AA: Typical: Elongation at Break: 12%: 12%: AA; Typical; 1/16 in. (1.6 mm) Thickness: Modulus of Elasticity: 68.9 Gpa: 10000 ksi:
6061 Alloy Uses. Corrosion Resistance. Heat Resistance. Heat Treatment. Machining. Welding. Conclusion: Aluminium 6061 is an alloy made
AA Standards Grade 6061 T651 View suppliers . Want to keep this datasheet? Save it now in your required format. 6061-T6 Aluminium – The Ultimate Guide.
6061 yield strength reduction initiates at about 250 – 300°C (Figure 20b) which is also about when the hardening rate (dσ/dε) begins to change (Figure
Type 5052 aluminum contains 97.25% Al, 2.5%Mg, and 0.25%Cr, and its density is 2.68 g/cm 3 (0.0968 lb/in 3 ). Generally, 5052 aluminum alloy is stronger than other
Yield Strength. Less than 10,000 psi. 30,000 psi to 39,999 psi. 40,000 psi or greater. Maximum Temperature. 250 Anodized Multipurpose 6061 Aluminum Hex Bars. A hard
Sheet Aluminum Plate Wholesalers. tensile strengths vary from 50 MPa for an aluminum to as high as 3000 MPa for very high-strength steels. Yield Strength. Yield strength of
